The Oceana 800 is designed to operate with the Inmarsat GSPS, LinkPhone and Fleetphone SIM’s to provide reliable voice, data and SMS communication services to anyone in a remote location on land or sea or for emergency backup communications.
Complete integrated solution
A Beam active Mast Mount Antenna (ISD710) is supplied with the Oceana 800 to provide a complete integrated solution that is ready for use anytime, anywhere. The Oceana 800 was purposely designed for maritime applications to meet an IP54 ingress rating making it suitable for onboard vessel communications the terminal can easily be used in any land based fixed site application.
Key Benefits and Features
For a maritime installation the 505* Emergency Calling facility from the OC800 puts vessels directly in contact with a maritime rescue co-ordination centre (MRCC) free of charge.
• High quality Marine Grade design, IP54 rating
• Dedicated Privacy Handset
• Bluetooth connectivity
• RJ11/POTS interface, cable runs upto 600m/2000ft
• Voice, SMS, SBD and Circuit Switched Data capable
• Tracking and SOS
• USB data interface
• Accessory / Ignition sense
• 10-32V DC power input
• AC Plug pack included 110/240 input
• Supplied with Active Mast Mount antenna ISD710
• Supports Active and Passive Inmarsat antennas
• Full certified, Inmarsat, RoHS, CE, IEC60945, AS/EN60950
• 1 year repair or replacement warranty
* 505 Emergency calls only works when using a FleetPhone SIM card.
Instant Message and Tracking Features
• Dedicated internal GPS receiver
• Tracking
• Periodic location messages
• SMS, SMS to email
• Location message sent upon button press
• Ignition ON/OFF reporting
• Remote location polling via SMS Instant Message Mode
• Single button press on terminal
• Instant GPS location messages
• Supports external “man down” pendant or button
• Remote clearing of alert via SMS
• Tracking/Instant Message content includes
o Message ID#
o Header
o Latitude/Longitude
o Speed
o Direction
Watch Oceana 800 Video
Oceana 800 is an all-in-one IP54 communications terminal specifically designed to be utilized in a wide variety of applications throughout the world.
The terminal has a dedicated full color LCD display, to allow the user to access menus and details within the terminal.
Instant Message button can be configured to send an emergency message, including the GPS position, to a predetermined IP, email address or via SMS to notify of an emergency. The Instant Message functionality can be configured to support automated periodic polling or instant message reporting with a single button press.
the Oceana 800 features 2nd SIM, this feature will override a primary SIM when a secondary SIM is inserted into a terminal. Calls will be charged to the secondary SIM if it is inserted.
Time Bandit, the 34.44 metre-long (113ft) boat, named after the motion picture of the same name, is only on a mission to capture king crabs rather than human beings. And ...
Beam’s Oceana 800 is used by adventurers Bob and Elaine Ebaugh on their two year long cruise in the Caribbean. They find the phone to be trouble free, reliable and ...
IP54 Rating 5 = Protected against dust limited ingress (no harmful deposits). 4 = Protection against water sprayed from all directions - limited ingress permitted.
BLUETOOTH® Legal
Bluetooth®
The Bluetooth® word, mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by BEAM Communications is under license. Other trademarks and trade names are those of their respective owners.
Time Bandit, the 34.44 metre-long (113ft) boat, named after the motion picture of the same name, is only on a mission to capture king crabs rather than human beings. And although the exterior of their boat looks similar to a pirate ship from yesteryear, both of them prefer to rely on the latest modern technology systems while working off Alaska in the Bering Sea. Along with their four-man crew, they put BEAM's Oceana 800 terminal accessing Inmarsat's new low-cost satellite phone service, FleetPhone, through its paces. "We were extremely pleased with the performance of the BEAM Oceana 800 Fleetphone - particularly the voice quality of the service," said Captain Andy.
Weather reports "We've been using it to call in for weather reports and to keep in touch with fish processors, as well as family and friends. Everyone we spoke to on the phone commented on its clarity saying they could hear us so well." The Oceana 800 FleetPhone Terminal phone was supplied by the BEAM Communications, with airtime from Inmarsat distribution partner Stratos.
Emergency calling It offers mariners a host of features, including global coverage for its voice, text and low-speed data services, as well as Inmarsat's SOS emergency calling capability and an additional SIM for multiple users. Brothers Andy and Johnathan Hillstrand and their crew may take to the seas in a vessel resembling a pirate ship. But unlike the buccaneers of old, they prefer to rely on modern communications like FleetPhone (Inmarsat's new low-cost satellite phone service) while fishing in one of the most dangerous seas on the planet. "We were anticipating that the sound quality and reliability of the terminal might not perform in the areas we venture to, but the phone exceeded our expectations." The unit even provided service going through False Pass - except for a very narrow spot with steep mountainous sides, and however to be fair this is a location where our old other satellite equipment could not provide any service at all, said Captain Andy.
Voice quality "And unlike our old satellite service, which couldn't be relied on 24 hours a day, with Fleetphone we found we could make calls at any time of the day and guarantee a connection". The voice quality of the FleetPhone came in particularly useful when the crew dialled into the National Weather Forecast Office in Alaska for weather predictions. Captain Andy said: "Getting the weather forecast can literally be a matter of life or death for s and voice quality is important because we have to state our position before we can get the forecast."
Reliable phone The brothers - who are both third generation Alaskan fishermen - named their boat after the movie, Time Bandit, because they say "the sea steals your time". But having a FleetPhone helped them make up for lost time, especially when it came to getting their catch processed. Captain Andy said: "Around 60 fishing boats get their crab catches processed at one of two plants, and we need a reliable phone to keep in contact with staff at the plants."
Adventurers in the Caribbean
Beam’s Oceana 800 is used by adventurers Bob and Elaine Ebaugh on their two year long cruise in the Caribbean. They find the phone to be trouble free, reliable and offers additional tracking capabilities compared to other phones. They also found the installation really easy, the system only have 2 components, the handset and the active antenna. Connect the antenna to the handset with a pair of pre-made coaxial cables, then connect the handset to either 12 VDC or 110 AC, with the supplied transformer and you are up and running.
Quality Calls With numerous calls back home the Oceana 800 only dropped out one call for the entire time. “Voice quality was very good, but you do have to allow for the conversational delay due to the distance to the satellite. Text, email and weather reports work quite nicely”, Bob Ebaugh said.
Additional tracking The Oceana 800 has an integrated GPS engine providing intelligent tracking and instant message reporting via SMS which offers additional tracking capabilities. The Oceana 800 phone will update your position several different ways:
1) When you press the “tracking” button on the phone 2) Automatically based on a user defined reporting period 3) When someone logged on to the tracking website asks for an update Oceana 800
Oceana 800 Oceana 800 is an all-in-one IP54 maritime communications terminal specifically designed to be utilized in a wide variety of marine applications throughout the world. The terminal has an integrated Bluetooth for voice communications, intuitive color LCD display that provides easy and convenient access to send and receive or to retrieve phone numbers stored in the terminal. The Oceana 800 operates with the Inmarsat's “FleetPhone” service and is supplied with a dedicated active marine grade antenna system to provide a complete integrated solution that is ready for use anytime.
Q.I can hear an alarm coming from the docking station or terminal.
A.
An alarm indicates that the docking station or terminal has detected a short between the positive and ground of its RF connections (Satellite and GPS). The short could either be in the unit itself, along the cables, or in the antenna.
If you hear the alarm, remove power immediately to avoid causing more damage to the setup.
To locate which component of the setup is causing the fault, please follow the steps below. Remember to only apply power briefly and immediately remove power when an alarm is heard.
Check if the short is within the unit:
Disconnect the satellite and GPS cable from the unit.
Switch the unit on.
If the alarm goes away, then the short is along the cable and the antenna path. Proceed to next step 3.
If the alarm is still present, then the short is within the unit. To fix this fault, we require for the unit to be returned to Beam for service.
Check if the short is within the cables:
Switch off the unit, connect the satellite and GPS cable to the terminal, disconnect the antenna.
Switch on the unit, if the alarm has disappeared, then it is possible there is a short in the antenna. Replace the cable when necessary.
If the alarm is still present, then the short is possibly within the antenna. Proceed to step 5.
Check if the short is within the antenna:
Switch off the unit.
With the cables connected to the unit, connect the other end of the cables to the antenna.
Switch on the unit, if the alarm came back, then the short is within the antenna. Replace the antenna when necessary.
Q.How do I use Data with my Beam Inmarsat docking station or terminal?
A.
To enable your Beam Inmarsat docking station or terminal for the data service:
Connect the docking station or terminal to your PC using the USB cable.
Initially you will need to install a standard USB Modem Driver to work with the unit station.
To do this, on your PC go to Control Panel > Phone and Modem options and select the Modem tab.
Select Add > make sure you tick Don’t detect modem I will select from list then NEXT >.
Select the Standard Modem type and 2400bps Modem. Click on NEXT > It will prompt you now to select the Comport that it is attached to.
Highlight the modem driver you have just created and click on PROPERTIES > ADVANCED.
In the Extra initialisation command key in the following: &FE0&D2 OK>
Place your phone into the Docking Station ensuring it has signal when inserted and ready for service. (If Applicable)
Identify the modem COM port to which your device is connected for the data service.
The COM port number will be needed when you are using your data application.
To do this, on your PC go to Control Panel > Phone and Modem options and select the Modem tab.
You will see Standard 2400 bps Modem and the COM port eg. COM6. Or, go to Control Panel > System and select the Hardware tab. Click on Device Manager and scroll down to Modems.
If your USB drivers are installed you will see Standard 2400 bps Modem. Right click on Standard 2400 bps Modem and select Properties. You will see the Com port eg. COM6.
To manage your data connection, install your chosen application if you have not already done so.
Q.Why does my Internet connection keep dropping while I am using the Internet?
A.
This problem occurs when there is poor signal quality. Users who are attempting to make data calls from inside of a building also tend to have this difficulty.
When your call drops, observe the signal strength indicator in the corner of the LCD on the phone or your computer and verify that your signal is in the range of 4 to 5 bars.
If you are not getting 4 to 5 bars of signal, you may want to adjust your antenna location to get a better view of the sky.
If the problem persists, please contact the dealer through whom you purchase service.
Is the card inserted the correct way? The notch on the sim card should align with the notch on the sim tray.
Check the SIM and phone contacts. If they are dirty, clean them with an anti-static cloth.
Is the gold chip visibly damaged or scratched? If so, contact your service provider for assistance.
Q.My SIM PIN is blocked, what do I do next?
A.
If you enter the PIN incorrectly 3 times, the SIM card locks, and you need to enter the PUK. You must use the PUK code supplied by your Service Provider to unlock the SIM. If you don't have a PUK code please contact your Service Provider.
Q.My Inmarsat Terminal (Oceana/Terra 800) shows Market Restriction on the display and unable to continue to the phone menu. What's wrong with my terminal?
A.
All Oceana and Terra series terminals shipped from Beam beginning of August 2015 have their market restrictions removed. This means these terminals can now use any Inmarsat GSPS, Fleet, or Link sims.
If you get a market restriction notification on your terminal, this means your terminal is still locked to a specific market and may only use a Fleet (Oceana terminals) and Link (Terra terminals).
To remove the market restriction, please contact This email address is being protected from spambots. You need JavaScript enabled to view it. for guidance.
If the Handset says its BLOCKED, it means you have entered the PIN 3 times incorrectly.
You need to enter your PUK code. This can be obtained from your service provider.
You can UNBLOCK a sim card via a range of different options.
Download the Sim Pin Configuration guide herefor the instructions.
Q.What is a SIM PIN?
A.
The Subscriber Identity Module (SIM) often referred to as a simcard, typically is provisioned and issued by a Service Provider (SP) with an associated Personal Identification Number (PIN), sometimes referred to as PIN1.
It is possible to request simcards without PINs. When the satellite device first powers on, if the unit is set to request that the user enter the PIN code then until this has been successfully completed the unit will not register, place calls or receive calls.
Q.My PIN2 is locked, what do I do now?
A.
Enter the PIN2 unblocking key (PUK2) or contact your service provider for further assistance.
Q.What does the message "Check Card" mean on my Iridium terminal?
A.
A “check card” message means there is something wrong with the sim card and how it is inserted/installed in the sim tray.
Usually, there is a contact problem between the sim and the sim tray.
A couple of things to check:
Is the sim card installed the right way in the sim tray? See screenshots below for reference only and may not represent your exact product.
Make sure the contacts are ok, no damage, etc. See screenshots below for reference.
Once all checks have been performed and the error message persists to appear, check the sim card with a different unit and see if the error message follows.
If the error message follows, then the sim or how the sim is inserted could be the problem.
If the error message stays with the unit, then try a new sim, if the error message still appears, then there must be something wrong with the sim tray or the unit itself.
Q.What is the maximum length of antenna cable I can use with my Active Inmarsat Antenna?
A.Antenna cables for the Active Inmarsat Antenna start at a length of 6 meters and go up to 100 meters. Custom cables can be made longer if required. Please see your Beam Authorised Reseller.
Q.What is the maximum length of antenna cable I can use with my Passive Inmarsat Antenna?
A.
Antenna cables for the Passive Inmarsat Antenna start at a length of 10 meters and go up to 50 meters. If you need to go longer, you may be better off looking at using an Active antenna to get access to the longer cable kits.
Q.The signal bars are low or fluctuating and the call quality is poor on my Inmarsat Service.
A.
Ensure that the following are observed:
All antenna connectors are hand tight. Not too tight as it will break the connection.
The antenna is installed in a location that has a direct line of sight to the satellite and there are no obstructions.
BEAM certified antenna cabling is being used and there are no sharp bends or cuts in the cable, and the cable has not been modified in anyway
If using a fixed passive antenna, ensure it is orientated correctly and pointing at the correct satellite.
Q.How do i know if my docking station or terminal is registered on the satellite network?
A.
On a docking station/ terminal with status LED, the Status Led will change to green when the terminal is registered to the network.
For an RST100 terminal, the signal LED will change from Red to Green.
For Oceana/Terra 400 terminals, the signal LED on the terminal will change to GREEN (Good Signal Registered) or YELLOW (poor signal registered) when it is registered and able to make calls on the network.
Refer to the product's user manual for more information.
Q.My Terminal / Docking Station continues to display "Searching Satellite / Network..." and never registers to the network.
A.
Ensure your terminal’s antenna is installed where there are no obstructions and has a clear line of sight to the satellite with no obstacles which could block the signal.
Check the antenna cable and all connections are secure and no bends or breaks / cuts in the cable
Check for any RF interference near the antenna that maybe causing problems. If there is, shut them down and re test, if works ok, then you will have to relocate the antenna elsewhere
Check with your service provider that the service has been activated.
For Inmarsat subscribers, check the coverage map to ensure service is available at your location or if there is service outage in the area.
If problem persists, contact your service provider.
Q.Does RF Interference affect the satellite signal?
A.
All wireless devices, including satellite telephones, are susceptible to RF (Radio Frequency) interference from other electronic devices. This problem is especially evident when numerous antennas and broadcasting devices are located within close proximity to each other.
A good example would be onboard a ship. It is important that certain considerations be taken into account for best performance when an Iridium/Inmarsat system is installed.
Causes of RF Interference:
Some subscribers have contacted Iridium regarding the loss of signal quality when they operate their equipment near active Inmarsat terminals. The power with which Inmarsat units transmit can overpower the Iridium unit’s ability to properly maintain a quality connection with the Iridium satellite constellation. Inmarsat terminals are often found in the same locations as Iridium subscribers, such as harbors, airports and especially onboard ships.
The location of the Inmarsat unit’s antenna in relation to the Iridium unit’s antenna plays a significant role in determining the degree of signal degradation that an Iridium subscriber can expect to experience. All Iridium units are susceptible to this interference, regardless of the type of antenna being used.
Generally speaking, an Iridium unit, be it a handset using its internal antenna or a fixed terminal when attached to an externally mounted antenna and located within 15 and 45 meters (50 to 150 feet, respectively) of an operating Inmarsat Standard-C terminal, will likely experience degraded performance.
Other sources of RF interference such as Globalstar units, radar devices and broadcast stations can provide interference for Iridium units, but usually are not encountered as frequently as Inmarsat terminals.
Also refer to “Assuring Quality of Iridium Service” in the Antenna Installation Guide.
Q.Why does my IsatDock display say "Deploy Antenna for Service"?
A.
The message "Deploy Antenna for Service" is displayed when the handset is inserted in the dock. But when handset is taken out from the dock and its own antenna is deployed it is able to get sat signal and make calls. No
When an Isatphone handset is docked and the message "Deploy Antenna for Service" is displayed, this means that the handset is not getting satellite reception when docked.
At this state, the handset display will not show any satellite signal bars until satellite signal is present.
Check the cable connections between the dock and the antenna.
Make sure the cables are tight enough, not too tight. Unscrew and screw back in the connectors to reset the connection.
Make sure the cables are connected to the right connectors (Satellite and GPS on the dock end should connect to the same ends at the antenna) It is also possible that the antenna has become faulty.
Swap the antenna with the exact same model to verify if the antenna is causing this problem. (For example, ISD710 to ISD710 or ISD700 to ISD700 only)
The Oceana/Terra terminals can store a maximum of 20 messages in its memory. If the memory is full, delete a few texts to free up memory for new messages.
If you still cannot receive a text, your service centre number may not be correct. Please refer to the manual in regarding to entering this in.
Q. Can I send SMS via the Comm Port?
A.
Yes, The user must use “AT Commands", through the data port. The AT commands use the standard GSM ‘PDU’ format.
Q.How can I send an SMS to an Inmarsat service - SMS-MT (Mobile Terminated)?
A.
SMS-MT messages can be sent to an Inmarsat phone/Beam docking station/terminal in one of 5 ways:
By sending an SMS-MO message from another Inmarsat phone. Current limitation is 160 characters.
By sending an SMS-MO message from a cellular phone ( if available ).
By sending an e-mail to This email address is being protected from spambots. You need JavaScript enabled to view it. where 870xxxxxxxxx is the 12-digit Inmarsat phone number. The subject line is ignored. “Plain Text” format is recommend for the e-mail message.
By sending an SMS-MO message from another Beam Inmarsat docking station/terminal, by using Falcon, SMS.
Q.How do I check/change the SMSC number?
A.
Check / enter Service Center Number:
Via the handset:
To enter the Service Center Number:
Press the ‘Envelope’ key.
Scroll to ‘Message Settings'. Press OK.
Scroll to ‘Service Center'. Press OK.
For an Iridium SIM, enter 00881662900005 or +881662900005.
For a Telstra SIM, enter +61418706700.
Via the Beam Management System (BMS) software:
Enter number in the “Settings - “Data/SIM” - “SIM/SMS” tab.
For an Iridium SIM, enter 881662900005.
For a Telstra SIM, enter 61418706700.
Click on another tab or field to commit the change in the Beam Management System (BMS) software. Please allow a few seconds for number to be displayed and changed.
Q.SMS Message sent, but recipient did not get it.
A.
Solution 1: Recipient phone # or e-mail address entered incorrectly. Make sure phone number was entered as 00 or +, Country Code, Phone Number. Make sure e-mail was entered with a space between the e-mail address and the message. For a Telstra SIM and Telstra SMS, the phone number is all that is needed, e.g. 0409xxxxxx.
Solution 2: Check expiry period. If recipient did not turn on their phone within the expiry period, message was deleted before delivery.
Q.Can I send an SMS to a device on another network?
Q.My Beam Inmarsat docking station/terminal cannot make or receive calls.
A.
Ensure the SIM card is inserted in the phone and is fully provisioned by your service provider.
For IsatDOCK's ensure the USB symbol can be seen on the IsatPhone display
Also, check if GPS fix is acquired.
If the phone has sufficient signal strength and cannot make or receive calls, check if Call barring, Diverting calls or Fixed number dialling have been activated.
If you have a prepay subscription, check your prepay balance to ensure you have sufficient credit to make a call.
Contact your service provider if you are unable to resolve the problem.
Q.Why am I experiencing more dropped calls than usual?
A.
Due to a satellite network, if you are in motion, the satellite signal may become obstructed (such as buildings, bridges, tunnels, larger vehicles, valleys , large trees). If your satellite setup is not obstructed and yet you have no signal, you will need to perform the following checks:
Check the antenna connections.
Ensure the antenna cables are not damaged.
Ensure that only approved antenna cable has been used.
Refer to Antenna Install Guide on Beam website support.
If problem persists, contact your service provider
Q.There is no audio from the external/handsfree microphone of Beam docking station/terminal. Party B cannot hear my voice.
A.
If your setup has an HFI Box:
Check that the slide-switch ON THE HFI is positioned to the left to enable the microphone 2.5mm jack (if applicable).
Check that the microphone connector is installed directly to the HFI kit (if applicable).
For other Beam docking stations:
Check the microphone is connected correctly to the docking unit (if applicable.)
Check if the cable is intact and has not come loose.
Q.Why is the voice quality poor on my Beam docking station/terminal?
A.
Voice quality may be affected by many factors. Before making a call, make sure that the signal strength is at least 4-5 bars (some terminals the signal LED should be bright green, not orange, or red). If the setup cannot achieve the signal level required, there is a possibility that there is a problem with the setup.
Please check FAQs about Signal or Antenna for more tips.
Q.Why does the microphone uplink audio sounds quiet when in handsfree mode?
A.
Depending on how loud the background noise is where the IsatDOCK is being operated, the unit's advanced DSP echo canceller may try to limit the microphone uplink audio to reduce feedback. In these instances it is recommended that users reduce the speaker volume by pressing the down arrow button on the lower keypad interface. Once the speaker volume has been reduced, the microphone uplink audio quality will improve.
Q.How do I use Bluetooth with the Beam Inmarsat docking stations?
A.
The Bluetooth functionality works from the IsatPHONE. Once the handset is inserted into the docking station Bluetooth will override the speaker. Once the BT headset is paired and connected, you will be able to hear the call progress tone in the dock’s speaker or privacy handset (if it is off the cup). When receiving a call, the ringer can be heard from the speaker but once the call is answered the audio gets connected to the Bluetooth headset.
One point to be noted here is that after the BT is paired it still needs to be connected as well. If it is not connected then it won't work!
To activate and/or connect to the IsatPhone via Bluetooth, refer to the IsatPhone Pro or IsatPhone 2 User Manual.
Q.There is too much echo while on a call when I am on hands free (using external microphone and speaker).
A.
Make sure the volume of the terminal is not on the highest setting as this will create echo, try turning it down a little.
Make sure the external speaker and microphone are not positioned too close to each other or not facing each other.
Q.I hear a lot of background noise while on the call.
A.
Make sure that the signal level is between 4-5 bars.
If you don't achieve that, check the components of the setup and the installation.
Check the location of microphone (if applicable), make sure it is not located near an air vent or too close to an open window.
Q.A call is established using the privacy handset but the other end (party B) cannot hear my voice.
A.
Check if the Mute LED is illustrating red. If so, the mute function is enabled. Press the Mute button once to disable the mute.
If the dock/handset is Bluetooth capable, check if the Bluetooth® LED is flashing blue at 1.5 second on and 1.5 second off rate.
If so, the Beam docking station is currently connected to a previously paired Bluetooth® device. Press the Bluetooth® button on the DOCK until a beep sounds to turn off the Bluetooth®.
Q.I cannot hear through the privacy handset/hands free option of my docking station. The handset gets signal when docked. I can make and receive calls but I can only hear through the handset and not through the privacy handset/hands free feature.
A.
The handset should recognise that it is docked, therefore the USB symbol on the handset should appear and charging is enabled.
Make sure there is power in the dock, the dock's buttons should light up.
If the USB symbol is absent, check the dock's USB connector whether it is broken or submerged. This fault needs to be returned to a Beam for repair.
If the USB symbol is present, and the speakerphone works, it is possible that there is a problem with the privacy handset. Make sure the privacy handset is plugged in the correct port, not the POTS port. Else, this dock needs to go back to Beam for repair.
Q.How do I activate and use the inbuilt GPS tracking functionality on my Beam docking station/terminal?
A.
The GPS Tracking feature can be activated/deactivated using the product's software management tool.
The software management tool can be downloaded from the product page in the Beam Communications website.
Q.A tracking/SOS alert keeps getting sent even after clearing it. How can I stop it?
A.
If an alert/alarm loop is used, make sure that a normally-closed switch is being used. A normally closed switch will only trigger once and therefore should not keep re-enable alert/SOS.
If the alert/alarm loop is not used, then disable the option ‘Activate emergency mode when the alarm/alter loop is broken’ in the Advanced Tracking options within the docking station/terminal's software management tool.
Q.How can I clear or stop a tracking/SOS alert?
A.
To clear the alert mode press and hold the Track button for seven seconds. A single beep will sound, and the LED will show the re-armed state (GREEN).
Q.Why is the tracking/SOS alert feature not working with an external button?
A.
If the alarm loop is used with an external normally closed switch/push-button, remember to enable this external loop in the software management tool settings. Once enabled, the loop will be armed and activated with an open-loop condition.
To avoid false triggering, be sure to have the normally closed button wired into the alert loop, before applying power.
Q.How does the GPS tracking work?
A.
The Beam terminals or docking stations with tracking capability supports periodic position reporting or manually activated position reports via SMS. The device can be programmed to send at a regular interval whenever the unit has power or alternatively whenever the TRACK button on the device is pressed.
The position report is sent via SMS to a predetermined destination which can be another SMS service or email address.
The device also support the use of an Panic Alert which is a two button press on the dock or via an external button input I/O to the dock to generate an Emergency Alert message from the device, this is also via SMS and takes priority over the periodic position message.
The device can also be remotely polled for a current position report. The SMS messages can be sent to your own designated tracing application.
Q.What is the proper torque value for the SMA connector?
A.
The proper torque for the sma connector is between 7 to 10 inch pounds of torque. (81 to 110 N-cm, for those who prefer metric measures).
If this value is exceeded, its possible to break the connector. Please note that if found the antenna connector has been damaged due to over tightening, this will void the warranty.
Q.Can I use a Passive/directional antenna with a IsatDOCK Marine?
A.
Inmarsat passive/directional antennas are best suited for fixed installations like buildings, homes, and the likes. The Inmarsat passive/directional antenna is required to permanently point directly to the nearest Inmarsat satellite. It is not suitable for mobile applications.
If you wish to use an Inmarsat satellite setup on a moving vehicle or vessel, consider an active/omnidirectional antenna.
Q.Can I use any kind of cable in combination with my Inmarsat active/passive antenna?
A.
Only cable kits supplied by Beam will operate correctly with the Inmarsat antennas. Each cable kit has been made to meet the specifications of the antenna and Inmarsat network.
The cable kit not only provides Satellite connectivity but also GPS which is required for the Inmarsat service to function correctly.
In the case of active antennas, then dock/terminal provides power to the antenna as well.
For example, use passive cable kits with the ISD700 and active cable kits with the ISD710 / 715 and 720.
Failure to use the correct Beam cables can damage the antenna, stops the service from performing properly and void warranty.
Specifications
Oceana 800 - DISCONTINUED Specifications
Inmarsat Transceiver
Inmarsat-4 Satellite
GMR-2+ Frequency Bands
Tx Operating Frequency
1626.5 - 1660.5 MHz
Rx Operating Frequency
1518 – 1565 MHz (Inmarsat)
1565.19 – 1585.65 MHz (GPS)
RF Output Impedance
50 Ohms
Carrier frequencies
Channel 0 = 1626.525 MHz
Channel 169 = 1660.475 MHz
TX Modulation
GMSK
RX Modulation
OQPSK
Power
Average Power Consumption (Active Antenna Connected)
Current @ 15V Average
Power
Standby
0.22A
3.2W
Transmit (RJ11/POTS)
0.58A
8.7W
Transmit (Speakerphone)
0.53A
7.9W
Sleep Mode
5mA
75mW
Peak Current
1.7A
26W
GPS Module (Internal)
Channels
14 tracking, 51 Channel Acquiring
Update Rate
1Hz
Accuracy
Position 2.5m CEP, Velocity 0.1m/s, Timing 300ns
Acquisition TTFF
Cold 29sec, Hot 1sec
Sensitivity
-161 dBm
Operational Limits
Altitude 18000m , Velocity 515m/s
Dynamics
4G
Connectors / Interfaces
POTS/RJ11
RJ11/2-wire, 5REN @ 600m, Adjustable dial, ring, busy tone configured frequency and adaptive impedance.
IP54 Rating 5 = Protected against dust limited ingress (no harmful deposits). 4 = Protection against water sprayed from all directions - limited ingress permitted.
BLUETOOTH® Legal
Bluetooth®
The Bluetooth® word, mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by BEAM Communications is under license. Other trademarks and trade names are those of their respective owners.
To configure the settings and update the firmware on the docking station/terminal:
Download and install the Software Management Tool to a compatible windows computer.
When available, download and follow the Installation Guide.
Make sure power is supplied to the docking station/terminal.
With a Serial/USB cable, connect the docking station/terminal to the computer.
Open the Software Management Tool and connect.
To update the transceiver firmware on the docking station/terminal:
Download the transceiver firmware on your desktop.
Open Falcon and navigate to Upgrade Firmware section.
Select Inmarsat Transceiver Firmware Upgrade.
From the drop down list, select Custom Firmware to use the file downloaded earlier.
Transceiver Firmware update will take at least 15 minutes. Make sure the USB connection is not interrupted.
For help on using the Software Management Tool, some have user manuals which are available to download from the tool itself by clicking on the ? or Help link.
Need more help? Contact support
